A wall can feel dry to the touch in a day while the studs and plates behind it stay wet enough to feed mold. Call Water Heater Repairer and we route you to an independent drying contractor in Ann Arbor who measures, maps and logs moisture until the structure reaches its drying goal.
Proper drying is applied psychrometrics, and it has little in common with leaving fans running for a weekend.
Calls go to independent local drying contractors who carry their own license and insurance. Plenty hold IICRC water restoration training; ask to see it at the door.
Drying is a race against wicking, so we prioritize contractors with dehumidifiers and air movers already loaded. Many arrive within the hour, though that depends on distance and storm volume.
You get the drying scope, the number of units and how they bill in writing before setup starts. That written scope heads off disputes over equipment days later.
The basic toolkit is pin and pinless meters, a thermo-hygrometer and a thermal camera. With them, the drying job runs on recorded numbers instead of hunches.
A familiar call goes like this: the leak got fixed, the floor feels fine, and yet the room smells musty a week later. Almost every time, the moisture is still sitting in the bottom plate, inside the wall cavity, or in the subfloor beneath the pad. Finding and pulling out that hidden moisture is the whole job of a structural drying contractor.
Callers also ask about the noise and what the equipment will do to the electric bill. Most setups run a handful of air movers and a dehumidifier or two nonstop, so a good contractor checks which circuits can carry the load. A few days of proper drying is cheap next to replacing cupped floors, delaminated cabinet boxes or mold-stained walls.
Every job opens with a moisture map and closes only when all readings reach target.
The contractor takes a dry standard reading from unaffected drywall, trim and flooring in the same building. That figure, near the material's equilibrium moisture content, sets the goal each wet spot has to hit.
Low-grain refrigerant units strip moisture from the air down to low grains per pound. In cold basements or with hardwood and plaster, a desiccant unit keeps drying where refrigerant coils fall off.
Axial fans move big volumes over open floors; centrifugal units aim tight, fast air along wall bases and under cabinets. Every unit goes where the moisture map says, not where it fits.
Rather than cutting walls open, many pros remove the baseboard and drill small holes behind where it sat. An injection system pushes dry air through hoses into each stud bay, and the trim hides the holes afterward.
Wet hardwood cups as the bottoms of the boards swell faster than the tops. Sealed drying mats or panels draw moisture up through the wood with steady suction.
A closed chamber uses poly sheeting to box in the wet zone, so the dehumidifier treats less air. That speeds drying and cuts noise and power draw in the rest of the house.
This is how a well-run drying job moves from day one to sign-off.
Tell us where the water came from, how long it sat and which rooms are affected. Those answers tell us whether you need drying only or extraction first, and we route the right contractor.
The pro shows up carrying meters, a thermal imager and a starting set of dehumidifiers and fans. Thermal imaging traces how far water has wicked up walls before anything gets moved.
You get a written scope: evaporation class, drying goals, equipment count, expected days and how billing works. Nothing runs until you approve it.
Daily visits record readings, shift equipment and remove units as each area hits target. The final drying log, with every reading dated, is yours for the insurance file.
Fans by themselves just stir humid air around; they do not take the water out. Once relative humidity climbs, evaporation slows and the drywall stops giving up moisture. Without dehumidification controlling grains per pound, the framing can stay wet for weeks.
| Evaporation class | What it usually means |
|---|---|
| Class 1 | Small area, little absorbed water |
| Class 2 | A full room wet, with water wicked up walls under two feet |
| Class 3 | Water from above, ceilings and walls saturated |
| Class 4 | Dense materials like hardwood, plaster or concrete holding bound water |
Get a structural drying contractor in Ann Arbor metering it today.
The dishwasher supply leaked overnight and by noon the floor looked totally normal. The drying contractor found the oak reading way above a dry board in the hallway and set up panels on it. It took five days, but the floor never cupped.
My adjuster wanted to cut two equipment days off the bill. I sent the daily log with moisture readings for every wall, and the full invoice was approved. Having those numbers made the conversation short.
A supply line burst in our office on a Friday and soaked three rooms. Instead of tearing out walls, the crew pulled baseboards and fed dry air into the cavities through small holes. They built a closed chamber, so we kept working in the front.
The water heater failed in our basement and we just ran box fans for a week. The smell would not go away, so we called and the pro scanned the walls with a thermal camera. Water had wicked up behind the paneling almost two feet. A desiccant unit and a few days of readings finally got it dry.
Most Class 2 losses reach their drying goals in three to five days. Hardwood, plaster and concrete can take longer because water is bound deeper in the material. The moisture readings decide when units get pulled, not a set number of days.
Each wet wall is measured against a dry standard read from untouched drywall elsewhere in the house. Once the numbers match that baseline, that wall is done.
Often they do not. For clean water in open stud bays, drilling behind the baseboard and injecting dry air often saves the wall. Wet insulation, contaminated water or mold growth usually means a flood cut.
Shutting them off at night lets the air get damp again and undoes part of the progress. Ask the contractor about a closed drying chamber, which confines the noise and power draw to the wet area.
LGR dehumidifiers run on chilled coils and shine in normal room temperatures. A desiccant unit pulls moisture with an absorbent wheel and keeps drying in cold basements or on dense materials.
Getting drying mats on quickly gives the boards their best shot at flattening out. Some mild cupping relaxes as moisture equalizes, so the contractor will usually recommend waiting before anyone sands.
Drying calls get routed to contractors across Ann Arbor and the surrounding suburbs, including 48103 48109 48104 48105 48108 48113. From downtown condos to split-levels on the edge of town, the approach stays the same: measure, map, dry and document.
Plaster and old hardwood soak deep and often call for desiccant units.
Water moves through shared walls, so mapping often covers the unit next door too.
Slab homes and finished basements around Ann Arbor get the same readings-first approach.
Whether the water came from a supply line, a water heater or an upstairs bathroom, call as early as you can. Each hour wet lets moisture climb walls and soak further into framing.
Call +1-877-637-9008
